|
|
That's
right. The SeaCURE Custom Mouthpiece molds to fit your mouth,
teeth, gums and jaws! It is scientifically designed by an
orthodontist to use you entire jaw for maximum retention and
control of the mouthpiece-regulator unit of your SCUBA equipment...without
jaw fatigue and headache pain sometimes experienced with conventional
mouthpieces. SeaCURE is even remoldable if your "bite" changes
due to dental work!
The SeaCURE Custom
Mouthpiece is easily molded to fit you precisely! It is safe,
durable and reliable. It fits most regulators. Above all, the
SeaCURE Custom Mouthpiece is a mouthful of diving comfort! |
|
SeaCURE
I - fits standard orifice regulators that have a conventional
mouthpiece retention lip.
Apollo; Bridgestone;
Coral; Dacor (new pacer model; not older pacer); Beuchat (VS-3,4&5);
Cressi-sub; IDI; Parkway; Halcyon Rebreather; Pro Sub (Avalon);
NDS; Nemrod, ; Scuba Pro; Seac; SAS; Sherwood (most early models/Brut/Magnum
II/Oasis/Pre 1992 Blizzards); Tabata/Tusa 500 Series; Early
Metal US Diver Models; and other standard size orifice regulators.
(SeaCURE cannot be
used on AERO model Dacor because of holes in body of mouthpiece
orifice) |
|
SeaCURE
II - fits intermediate size air orifice regulators.
Apex; Atomic Titannum;
Beuchat (VS-6&10); Chiaro; Mares newer model but not on
Mares MR12II, III, IV or V); IST; Ocean Edge; Tekna; Oceanic;
ProSub (larger size); Seaquest (not air source);Sherwood Maximus/Oasis
2/1992; Newer Blizzard; New Maximus (requires Professional Model
only, the diver can grind one side of the internal core of the
mouthpiece to maintain and venturi effect); Zeagle; and other
intermediate size orifice regulators.
Poseidon/ Sherwood
Ultima - While SeaCURE is not designed to fit Poseidon of Sherwood
Ultima, many divers are now using a Pro Model SeaCURE II with
these regulators. It takes considerable extra effort and strength
to mount SeaCURE II, but it will go on the plastic models, not
on early metal units. (Never place the regulator end of SeaCURE
into boiling water but only warm tap water on it for 2-3 seconds
and a small amount of soap or spit on the orifice may also help
ease it on. No other lubricant should be used. DO NOT USE SPORT
MODEL ON ANY POSEIDEN OR SHERWOOD ULTIMA (IT WILL SPLIT)) |
|
|
SeaCURE III - Fits
US Diver Plastic Regulators, new Seaquest, Genesis, & SeaMech
US Diver regulators
do not have the conventional retention lip on the mouthpiece
orifice common to all other regulators and therefore no other
SeaCURE model should be used on Plastic US Diver regulators.
Snorkels - SeaCURE
fits removable mouthpiece snorkels on the market. The SeaCURE
model that fits is noted where known.
Amico (I); Cressi-sub
(I); Dacor 3 models (I); Netex (I); Ocean Reef (I); Reef Buddy
(I); Tusa 500 Series; IST; Parkway (II); Pic (II); Techisub
(II); Ocean Master, Dry2000 (III); ProFlo SQC (III); Trident;
US Diver (III).
not listed above If
possible, try both SeaCURE I and SeaCURE II on the unit in question
to see which fits. Otherwise, simply measure the retention lip
on the air orifice of the regulator. The results of a recent
survey of regulators indicate that almost all fall into two
general sizes with some in each group being slightly larger
or smaller than the average |
| |
Standard
Lip - (1-1/4" x 3/4") takes SeaCURE I
Oversize Lip - (1-7/16"
x 7/8") takes SeaCURE II |
|
|
|
|
